Gate Repair KL & Selangor – Gate Fell Due to Rusty Hinges and Steel

A few months ago, this customer started to notice that her main gate was slowly getting into bad condition. The gate had been there for many years, and some parts of the steel had started to rust and become weak. At first, the problem did not look too serious. She did not want to replace the whole gate with a new one. She preferred to repair the existing gate if possible.

Over time, the problem became worse. The gate hinges started to become lower and lower, and the gate slowly dropped out of its original position. She could still open and close the gate, but it was getting harder to use. She knew that something needed to be done, but she wanted to repair the gate instead of spending money on a completely new gate.

Gate Fell and Need Urgent Autogate Repair

After a few months, the condition became too bad. The steel around the gate hinge had become weak, and the hinges could no longer hold the weight of the gate properly. One day, the gate finally fell down.

She then started looking for someone who could repair the gate. She contacted a few companies and contractors, but she found that not everyone wanted to take on this type of gate repair job. Some contractors said the gate needed to be brought back to a metal workshop for welding. Some gave a much higher repair cost. Others suggested replacing the gate instead. But she still wanted to keep her existing gate if it could be repaired safely. That was when she found EE Automation & Technology Sdn Bhd.

We Came With a Lorry and Gate Spare Parts

After checking the condition of the gate, we found that the problem was not only the hinges. The steel at the end of the main gate had also become weak and bent. This part was important because it helped support the gate and the hinges. If we simply changed the hinges without repairing the damaged steel, the problem could come back again. So, we prepared the necessary tools, steel parts and spare parts and came to her house with our lorry.

Our team carried out the repair on site. We removed the damaged section and replaced the bent and weak steel at the end of the main gate. We also replaced the old gate hinges and carried out the necessary welding work. After that, we adjusted the gate back into the correct position and checked that it could open and close properly.

Gate Repair Done On Site

One of the things customers often ask us is whether the whole gate needs to be taken away for repair. For some jobs, workshop work may be needed. But for this gate, we were able to carry out the repair on site. This made things easier for her because she did not need to arrange for the gate to be removed and transported to a metal workshop.

We came with our lorry, tools and the required spare parts and worked on the gate at her house. After the repair was completed, we checked the gate several times to make sure it was sitting properly and could be opened and closed smoothly. The gate was no longer hanging as low as before, and the new hinges and repaired steel were able to support the gate again.

You May Not Need a New Gate

Many homeowners think that once a gate becomes old, rusty or starts to fall, the only solution is to replace the whole gate. This is not always the case. Depending on the condition of the gate, it may be possible to repair the rusty or damaged steel, replace the hinges and carry out welding work instead of making a completely new gate.

Of course, every gate is different. We need to check the actual condition first. If the main frame is still in reasonable condition, repair may be possible. For this customer, she wanted to keep her existing gate, and we were able to repair the damaged parts and make the gate usable again.

Don’t Wait Until Your Gate Falls

If you notice that your gate is slowly getting lower, the hinges are dropping, the gate is becoming difficult to open, or the steel around the hinges is starting to rust, it is better to check the problem early. A small gate hinge problem can become a bigger problem when the gate is heavy and the supporting steel has already become weak.

In this case, she noticed the gate getting lower for several months before it finally fell. If the problem had been repaired earlier, the repair may have been much simpler.

Need Gate Repair?

If your gate is falling, the hinges are damaged, the steel is rusty, or the gate needs welding, give us a call. Mr Sam from EE Automation & Technology Sdn Bhd can help with:

• Gate repair
• Gate welding
• Gate hinge replacement
• Gate roller replacement
• Rusty and damaged gate repair
• Gate alignment and adjustment
• General gate maintenance

For suitable repair jobs, we can come to your location with our lorry, tools and spare parts and carry out the repair on site. You don’t always need to replace the whole gate. Sometimes, repairing the damaged steel, hinges or rollers can give your existing gate a new lease of life.

Please call Mr Sam for gate repair and welding: 012 – 405 8791
WhatsApp Mr Sam 012 – 405 8791
EE Automation & Technology Sdn Bhd – Gate Repair, Gate Welding & Gate Services