Ranger Underground Autogate Installed in 2006. Now Having Problems …
An old customer called about an underground autogate they had installed by us in 2006. Now they are having problems with their Ranger’s center lock and broken rubber stopper. Back then, their car porch was made of concrete cement floor. The underground autogate is functioning properly without any issues.
But they renovated their house, and now the car porch is covered with pavement bricks. I recall advising them not to use pavement bricks for the renovation. It seems they may have proceeded with using bricks neglect the recommendation.
Autogate Lock Problems With Interlocking Pavement Bricks
Another big issue is that you cannot install a water filter or autogate stopper on pavement bricks. This is because the anchor wall plugs used for installation will not be securely tightened. The nature of pavement bricks does not provide a stable surface for securing these types of fixtures properly. It is important to consider carefully if you want to use pavement bricks.
The same issue applies to pillars made with bricks. We strongly advise against using bricks for constructing pillars because they present similar challenges. Bricks do not provide a secure and stable surface for installing the anchor wall plugs for the autogate arm brackets. It is recommended to use FULL CONCRETE pillars to ensure the proper installation and functionality of these components.
More Problems With Pavement Bricks
Here are more pavement brick problems. If the pavement bricks are not installed correctly, some problems can occur. The bricks may become uneven and start to tilt. This happens when the sand between the bricks is not swept in properly and the bricks are not pressed down firmly into the ground. Another issue is when water collects on the bricks, forming puddles. This could mean that the ground underneath was not sloped correctly or that it was not packed down enough, causing it to sink over time. Uneven bricks of different heights usually happen when the ground underneath is not dug deep enough or is not level. If the soil in the area is clay, it holds more water than sandy soil, which can make the problem worse.
Underground Autogate Lock and Rubber Stopper Replacement
The underground center lock of the autogate is experiencing problems, including a non-functioning solenoid coil, the failure of the underground drop bolt to engage and lock the gate, and a worn-out auto gate rubber stopper. To resolve these issues, we need to replace the solenoid coil in the center lock and also replace the worn-out rubber stopper.
Now the problem is that the pavement bricks are not strong enough to support the installation of anchor wall plugs. So what can we do? To install the rubber stopper securely, one option is to remove some of the pavement bricks, put steel bars in the ground, and make a concrete base. But this solution can be quite expensive, including the cost of the center lock, rubber stopper, and the construction work. Due to the high cost involved, it may not be the best recommendation.
Best Autogate Solution To Solve His Problems – FBM 989
We suggest using our FBM-989 stainless steel arm autogate as a replacement. The good news is that the FBM-989 doesn’t need a center lock to work properly. This option can solve the issues with the pavement bricks and offer a more reliable autogate experience. Our FBM 989 autogate is built to be sturdy and durable, featuring a solid steel mechanism inside. The autogate arm mini DC motor it utilizes is known for its exceptional power. The autogate PVC box contains high-quality autogate components such as a autogate S3 control panel, autogate power transformer, autogate remote control operating at 433MHz, and a reliable autogate backup battery. These components are carefully selected to meet high-quality standards. It’s important to note that all components used are 100% brand new and authentic, ensuring optimal performance and longevity of the autogate system.
Meet Old Friends Again
It’s very nice to hear that the customer has been using our Ranger brand underground autogate for 17 years and finds it to be a great value for the money. Due to their positive experience, they readily accepted our suggestion and scheduled an installation. The customer was happy to talk to us again after many years and felt a friendly connection with us, like old friends. We are excited to serve them once more and provide excellent service.
Call EE Automation For Autogate Replacement Or Spare Parts
We carry the spare parts for the following underground autogate brands, including Aprigate, Baxter, BCM, CEI, Chubb, Comex, CPT, DKC, Door Guard, Door Mex, Elock, EPL, Gatium, Good 1, Letron, Li Gates, Mag, Powergates, Radion, Radeon, Ranger, Snontec, Supermax, Techno, Victor, Wheels, and 100 Super A. This customer is using Ranger brand autogate with SWG800 Controller.
If you are looking for a new autogate system to replace your old underground autogate motor, don’t hesitate to call us. Or if you need a replacement for your old underground autogate or specific replacement parts, kindly take a few pictures of the items you require, and we will be happy to assist you. You can contact Mr. Sam at 012-405 8791. We are dedicated to providing you with the best autogate service possible.
